Herbold Mechesheim, the machine and plant manufacturer from Meckesheim, Germany, will present its five columns for efficient and cost-effective recycling of plastic waste, characterised by low operating costs and a higher efficiency.
Herbold
Herbold Wet Shredder HGM 60/200
Column 1: Pre-size-reduction
Pre-size-reduction is an important process step if the feeding material is too bulky for the usual procedure or if the material is in a first step only to be coarsely shredded for sorting, classification or inspection. For this purpose, shredders, granulators, guillotines and hammer mills are used as pre-size-reduction machines.
Herbold
HGM 60/200 Swivel-type Screen Support
One such system is the HOG Shredder HGM series, which is designed for size-reducing difficult materials, especially viscous materials or materials containing foreign bodies where the service lives of standard granulators are too short and where traditional shredders do not yield the desired end product. The HOG Shredder is available in wet execution for extremely abrasive materials, such as agricultural film, WEEE, etc.
Column 2: Size-reduction
Herbold size-reduction machines grind all types of plastic waste, it does not really matter whether it comes from injection or blow moulding, thermoforming, rotomoulding, flat film extrusion or blow moulding extrusion, calendaring or waste from the production of pipes, profiles and plates or from the manufacture of other plastic products. For example, patented Herbold granulators with forced feeding of the SB type (Granulator SB with forced feeding) have been successfully in operation worldwide for many years now. The material is not fed into the grinding chamber by gravity, as is the case with traditional granulators but as a continuous and even flow by means of feeding screws.
Herbold
Herbold Granulators SB with forced feeding
In case of difficult applications, only a few suppliers in the market are able to find an appropriate solution. The problem’s solution is the rotor design of the SMS Granulator.
The one-piece rotor guarantees stability. Welding seams cannot break since they do not exist. The knives of this rotor cannot shift because they are crewed onto a massive back limit stop. This special design facilitates cleansing as there are no 'dead angles' where remnants of grinding material could deposit.
Herbold
Rotor of the F Series with exchangeable wear protection
Column 3: Fine Grinding
Fine grinding for Herbold means pulverising below 1mm. For this purpose – depending on the product – Herbold uses granulators or impact disc pulverisers such as the Impact Disc Pulveriser PU Series. Herbold impact disc pulverisers are high-speed fine grinders. They are used with granular and brittle materials, for example PE granules or rigid PVC grinding materials.
Column 4: Washing, Separating and Drying
End of life post-industrial and post-consumer plastic products are used, mixed and contaminated plastics. Before they can be used again, they have to be washed and/or separated. With the successful commissioning of the film washing line at Rodepa Plastics B.V. Herbold Meckesheim proved that a high-quality end product can be obtained by separating undesirable plastics with the hydrocyclone separation step.
Mark Langenhof Managing Director from Rodepa Plastics B.V said: “Rodepa has taken a big step forward in recycling contaminated waste that is to newly integrate the production of film. This has only been possible with the best plant engineering. With Herbold Meckesheim we have now found the ideal partner in order to cooperate successfully.”
Herbold
Hydrocyclone and dryer, in the background prewashing unit
Complementing this stage is the HV ST-150/150 Series Step Dryer. The vertical step dryer consists of a multiple-stage rotor dewatering the material via a screen basket. The granules/grinding material water mass enter the machine from the bottom and are transported upwards by conveying blades. The diameter of the rotor increases upwards following the single steps. In the lower area (where free water can still be separated easily) only inferior circumferential speeds occur, at the highest step, drying is done with maximum circumferential speed. The step dryer is ideal for drying grinding material or granules of all different types of thermoplasts such as polycarbonate, polyethylene, polyamide, polypropylene and polystyrene. This machine is particularly suitable for drying brittle plastics and guaranteeing at the same time the least possible material loss caused by fines. The step dryer yields a residual humidity in the range between 0.4 and 0.06 per cent/weight. The machine is also available in a gas-proof execution for drying in an inert atmosphere.
Column 5: Agglomerating / Densifying
With extreme materials such as stretch film or foams, a sufficient mechanical or thermal drying is not possible without high energy consumption. The solution to this problem is the Herbold Plastcompactor, a modern compacting machine. The friction originating between the compacting discs of the compactor heats, dries and compacts the material at the same time. The recycling of PET bottles has a double advantage: the material is being crystallized at the same time. The end product is agglomerated material with excellent flow properties and a high bulk density, ideal for dosing and mixing.
Herbold
Herbold Plastcompactor HV 70 Series
Hall 9, Booth B42
